HIGHLIGHTS OF THIS MACHINE:
- Quill DRO Included Standard (This is for the spindle up/down movement)
- Belt Drive Design, For Smoother, Quieter Running
- DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped)
- Extra Large Column To Base Mount
- 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity
- 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling – Much improved over the single bolt mount type
- Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range
- .001″ Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately – (One line on the dial is .001″, one full turn of the handwheel is .100″, much easier to use than those with odd metric conversions)
- 50-3000 RPM variable speed with the turn of a knob, properly set up with Low and High for a wider speed range, and plenty of power at lower speeds
- Precision ground ways for smoother movements – Not just rough milled
- Thrust Bearings in leadscrew ends – not bushings – Much smoother movements and less backlash
- Split nuts on X and Y Axis to allow for backlash adjustment
- 3 Year Warranty
Standard Equipment:
1. PM-30MV Milling Machine
2. Chip Tray
3. Variable Speed with Belt Drive and Brushless DC Motor
4. Way Cover Set
5. Drawbar
6. R8 Spindle Taper
7. Quill/Spindle Depth DRO
8. Spindle Locking Wrench
Optional Accessories:
1. Stand
2. 3 Axis DRO Installed Note: if a 3 axis DRO is added to the machine, the 3rd axis of the DRO reads the HEAD up and down, Not the quill, so it is not doubling up on the measurement. If you add the 3 axis DRO, now both Z Axis movements are covered)
MAIN SPECIFICATIONS:
- Spindle Speeds: 50-3200 RPM, 2 Ranges (50-1400 in Low, 100-3200 in High)
- Spindle Drive Type: MultiV Belt (For smoother running)
- Motor Drive Type: VFD
- Table Size: 9″x31.5″
- Max. Table Load Capacity: 300 lbs
- Table T-Slot Size and Number: 14mm / 9/16″, 3 Slots
- Table Travel, X Axis: 22-3/8″ Hand Only, 19.5″ w/ Power Feed
- Table Surface Height from floor, 34-3/4″ (With base flat on floor)
- Base Dimension at floor approx. 18-5/8″W x 27″D
- Bolt Mounting Pattern, Milling Machine Base (Where the machine would bolt to either a work bench or to the cast iron base) Approx. 12-3/4 Wide x 18-3/4 Deep, 9/16” Hole Diameter
- Base of machine casting, bottom of the mill where it would mount to the optional base is approx. 24″ Front to back, 16″ Wide
- Normal Working Max Height: (top of column travel motor) 76-1/2″ (with optional stand)
- Height with head all the way up: (top of main motor) 81-1/2″(with optional stand)
- Stand (Base) height, to machine mounting surface: 24″
- Cross Travel, Y Axis: 8″
- Head Vertical Travel: 17″
- Max. Distance Spindle to Table: 18″
- Quill (Spindle) Travel: 5″
- Lead Screw Type: Inch Pitch Acme Threads
- Spindle Taper: R-8, with 7/16-20 drawbar thread (U.S.
- Standard)
- Quill Diameter: approx. 3″
- Head Tilt Front to Back: N/A
- Head Swivel: Side To Side, 90 Degrees
- Ram Swivel: N/A
- Power: 220 Volt, Single Phase, 12 Amps
- Motor Horsepower: 2 HP
- Casting Type: Fine Grain Cast Iron
- Country of Origin: China
- Approximate Weight: 1000lbs with Stand, 750 Without Stand
- Cord Connection/Type: Cord approx. 5′ length, User to supply plug needed for your outlet (20A 240V With Ground, No Neutral Required)
|
